Click here for menu

Repair Polaris 280 Sweep Hose Not Working (Solved)

Home > Pool Cleaner > Polaris 280 Sweep Hose Not Working

Polaris 280 Sweep Hose Not Working

Contents

Remove the top cover and check to see if the turbine feed hose is connected and the drive shaft is spinning freely. However, if you need more troubleshooting, you can take it to your local Polaris dealer and have them take a look at it for you. It may be necessary to install a ladder guard kit (part #G-21) to keep the Polaris 280 from getting stuck on the ladder. Check that all wheels are turning when in operation. this contact form

The tail does not whip any more. Is your Polaris going really fast around the pool? (DIY):16K Gal 20X30 rectangular IG Gunite, w/spa, CCP 520 filter,2 Pentair VS pumps, 400KBTU Pentair gas heater, Heat Pump for cooling, **update5.25.2013** Open it too little and it won't move at all. If it is moving to the right too often, move the jet to the right a fraction.

Polaris 360 Tail Does Not Sweep

My Polaris runs on its side. NavigationHow Do I Figure Out What is Wrong With My Pool? Your back up valve should pull the polaris off the steps. Call toll free: 1-888-959-5248 M-F 9-5 CST Your Cart is Empty Pool Supplies Most Popular Categories Pool Equipment Pool Cleaners Pool Pumps Pool Filters Pool Heaters Eco-Friendly Equipment See

Check that the feed hose nuts and swivels are not leaking any water. Thanks for your question Kim! We invite you to please Register to create a new account. Polaris Backup Valve Troubleshooting To know if it is working properly, lift it out of the water when the Polaris is running.

Mark the single wheel and count the revolutions of the wheel for one minute, beginning after the Polaris has completed a back-up cycle (back-up jet off). Polaris Pool Cleaner Tail Not Moving Push down on the idler wheel to dislodge any sand or dirt. Tweet Share34 Pin20 Share4Shares 58 When I post videos on the Swim University YouTube Channel, I encourage viewers to ask me questions about their pool problems on Facebook. https://www.swimuniversity.com/polaris-pool-cleaner-stopped-moving/ If the Polaris cleaner regularly displays the following actions, adjustments may be necessary to restore performance.

Turn the screw counter clock wise to increase the water flow to the sweep hose. Polaris 3900 Pool Cleaner Troubleshooting If this is the case the tires and/or the swing axle kit may need to be replaced. Or you need more pressure at the wall. Estimate finish 1st week March, 2014 Dimensions 37 x 24 x 17 feet.

Polaris Pool Cleaner Tail Not Moving

If the wheel gears are undamaged but not connecting with the drive shaft then you will need to replace the wheel bearings and/or adjust the axle.

If the wheels are all http://www.epoolshop.com/polaris_280_Troubleshooting.aspx Why does the Polaris 280 not climb the walls? Polaris 360 Tail Does Not Sweep This is a pretty easy fix. 3. Polaris 280 Pool Cleaner Troubleshooting If not, replace the Drive Belt (8) Check the filter screen (44) in the Quick Disconnect (41) and clean if necessary.

If it is too loose, it will not have enough tension to move. weblink Out - more tail flow In - less. WEBSITE: http://www.swimmingpoollearning.com/ Category Education License Standard YouTube License Show more Show less Loading... Sign In Sign Up Browse Back Browse Forums Blogs Calendar Staff Online Users Activity Back Activity All Activity Search Blog HomeGet Started Store InfoSome Samples About Us Sitemap Contact Us Polaris Polaris Pool Sweep Troubleshooting

If a swivel is leaking or not moving then it will need to be replaced. I haveĀ a customerĀ that has the precursor to this one, the Polaris 180, the sucker is 25 years old. Top Question: My Polaris 280 always gets stuck on the steps and light. navigate here Swimming Pool Tips, Reviews & How To -MrDgvb1 122,140 views 4:43 Polaris 280 - How-to Install Tune-Up/Rebuild Kit - Duration: 8:35.

It is easy to check the RPM by bringing the cleaner to the edge of the pool while keeping it submerged, turn it so the single side wheel is up. Polaris Pool Cleaner Floating Also, make sure the piece isn't broken. Check that the filter 280 bag (key number 1) is not full of debris.

You want all of the cleaner to stay on the surface of the pool unless the backup jet is working.

Swimming Pool Tips, Reviews & How To -MrDgvb1 683,967 views 8:42 Polaris Quick Disconnect Threaded Fitting Stuck in Pool Wall -Solution - Duration: 3:49. Thrust Jet: B. Mine was located at the base of the hose that attaches to the pool liner. Polaris 380 Tail Not Sweeping If the Back-Up Valve is working, and the tail is waving back and forth, but the wheels aren't turning, open up the cleaner and look for the belts.

Top Question: Why does my Polaris 280 only go in circles? The cleaner moves along the bottom, climbs the wall, etc. Check that the Polaris 280 is operating at optimal number of wheel revolutions per minute. his comment is here Look to see if water shoots out of the back-up valve.

Top Question: What causes my Polaris 280 to lay on its side? Reply With Quote 02-13-2012,08:07 PM #6 Lershac View Profile View Forum Posts View Articles Join Date May 2007 Location Baton Rouge, LA Posts 1,215 Re: Polaris 280 tail sweep inop Simply disconnect the wall connector and clean out the small debris basket (looks like a Thimble).If you find the Polaris on it's side in the bottom of the pool, the rear Share this post Link to post Share on other sites joey65 0 Newbie Members 0 2 posts Posted May 14, 2008 · Report post I have never rebuilt it (4years

Please try the request again. If water is spraying out of a crack in the housing of the back-up valve then you may be able to replace just the case kit. This cleaner will even pick up small river rock, screw drivers, ex girlfriends, ... Action: Polaris is sluggish, running with less power than normal.

the polaris unit is moving and vacuuming and there is water going through the sweep... You decrease the water flow by turning the screw clockwise.