Click here for menu

How To Repair Polaris Pool Cleaner Not Working Tutorial

Home > Pool Cleaner > Polaris Pool Cleaner Not Working

Polaris Pool Cleaner Not Working

Contents

The tail should have a soft, lazy back and forth motion. My relief valve is on the T fitting that connects to the Polar hose to the water discharge fitting on the pool side wall. Contacting Polaris Customer Service If these solutions do not result in improved performance, contact the Polaris Customer Service. To know if it is working properly, lift it out of the water when the Polaris is running. this contact form

Add a sweep hose weight to keep the sweep hose from spraying. Make sure this is clean and free of any sand or debris. Roboutique ro 7,694 views 3:56 Polaris 280, 380 & 480 Pro Installation and Walk-Thru - Duration: 8:18. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

Polaris 280 Pool Cleaner Troubleshooting

All wheels should turn together. Jason Hughes 736,888 views 7:55 Sluggish Polaris 380 Pool Cleaner - Duration: 5:52. Sign in to add this video to a playlist. All Rights Reserved

  1. Swim Goggles Is There adequate Water Pressure? – next, make sure there is adequate water pressure being delivered to the cleaner.
  2. Swimming Pool Tips, Reviews & How To -MrDgvb1 241,322 views 4:41 Polaris 280 - How-to Install Tune-Up/Rebuild Kit - Duration: 8:35.
  3. Hold the valve out of the water and watch the jet.
  4. Inside of a polaris, for example, the WMS(water management system) pushes the water through a small jet that sprays the paddle wheel (turbine).
  5. All wheels should turn together.
  6. Working...

Easily fixed by adjusting the float on the 360 closer into the 360. they should be...floating. Shanyz Ibrahim 233,601 views 4:19 Loading more suggestions... Polaris Pool Cleaner Floating An easy way to tell if this is your problem is by lifting the cleaner off the bottom of the pool and seeing if all the wheels are turning.

I got this question over the summer, and I figured I'd answer here in a post so that others could benefit if they have the same issue. Polaris 3900 Pool Cleaner Troubleshooting Sign in to make your opinion count. Doing this will give you full access to the forums, where you will be able to receive personalized advice concerning your pool.

With the bag off, and the pool cleaner sitting on deck, these jets will normally shoot 20 ft in the air. 8.

Too much hose and the cleaner will not work properly.The Back-up Valve must be installed 14-20 inches from the cleaner and the water opening (where water shoots out of) must be Polaris Pool Cleaner Manual When I lift the hose out of the pool water comes out of these fittings. With the Polaris turned off, spin each of the wheels. Page 9: Iii.operation And Maintenance, A.

Polaris 3900 Pool Cleaner Troubleshooting

Check the Tires, Rotate if needed. http://www.epoolshop.com/polaris380poolcleanertroubleshooting.aspx I agree with all these tips. Polaris 280 Pool Cleaner Troubleshooting Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Polaris Backup Valve Troubleshooting Hold the valve out of the water and watch the jet.

Loading... weblink Head Float: Affects the ballast of the cleaner: the recommended setting is all the way forward. Storage, I. Removing the top to the side, a screwdriver can be inserted behind the wheel to loosen two screws. Polaris Pool Cleaner Tail Not Moving

Check the wheel RPM. It only climbs the walls by about a foot if it happens to hit it head on, although running it once without the mesh filter bag it seemed to climb all Much slower than that and you may need to find out where the pressure loss is. http://brsgrp.com/pool-cleaner/polaris-pool-cleaner-tail-not-working.html A Troubleshooting Guide - Duration: 7:55.

Since the Polaris 280 is a pressure side pool cleaner, it needs a adequate number of water pressure to function properly, and without the requisite pressure it will not move. Polaris 360 Tail Not Sweeping If not, replace the Drive Belt (8) Action: Polaris doesn't back up. WEBSITE: http://www.swimmingpoollearning.com/ Category Education License Standard YouTube License Show more Show less Loading...

Sweep Hose Adjustment Screw: Regulates water flow to the sweep hose; the recommended setting is adjusted to provide a gentle sweeping motion.

I'm having the exact same problem with mine. Clean the skimmer basket, pump basket, and pool filter. Make sure the arrow on the swivel is pointed towards the Polaris and don't add a swivel within 10 FT of the Polaris (otherwise it will do 360 all day).Note: Also Polaris Pressure Relief Valve MonkeySee 13,820 views 4:47 Polaris 360 pool cleaner box tour video by POOLCENTER.com - Duration: 5:07.

Watch Queue Queue __count__/__total__ Find out whyClose Pressure Pool Cleaner Troubleshooting Tips MonkeySee SubscribeSubscribedUnsubscribe471,583471K Loading... These belts should be snug, but not too tight. When this happens, everything else could be working great, just the wheels can’t turn. his comment is here Solution: Make sure the opening at the end of the sweep hose is not blocked by the sweep hose scrubber.

Winterizing, J. All Rights Reserved. About Contact Advertise Privacy Terms Skip navigation UploadSign inSearch Loading... Sign in to report inappropriate content.

It is a new unit. These valves tend to fail often. Click here to learn more » You're All Set! If not, replace the Drive Belt (8) Action: Polaris flies around the pool and/or does not make contact with the bottom of the pool.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...