Click here for menu

Repair Pool Filter Not Working (Solved)

Home > Pool Pump > Pool Filter Not Working

Pool Filter Not Working

Contents

First, look up your pump in the manufacturer's literature or supply house (Poolcenter.com!) catalog to determine what model seal you need. If your pump is loud, the first thing to do is to listen to it. If the shaft is not spinning then the bearings have frozen and locked up the shaft. Anything that disrupts that harmony may result in loss of circulation, even though the pump is physically operating. navigate here

Something prior to the filter is obstructed. Swimming Pool Tips, Reviews & How To -MrDgvb1 167,637 views 7:15 Repairing a Pentair Whisperflo pump and motor part 1 - Duration: 9:45. The pump is meant to operate air free, to create the necessary vacuum. Remove the ‘donut’ seal half of the impeller that is pressed into the seal plate with a flat head screwdriver. http://www.inyopools.com/Blog/8-answers-to-why-is-my-pool-pump-not-working/

Pool Pump Not Turning On

Any further ideas? Air in pump basket? It is not necessary to remove the entire pump from the plumbing system.

Swimming Pool Tips, Reviews & How To -MrDgvb1 395,693 views 9:10 Cloudy Pool Water, Causes and Cures - Duration: 8:42. If that didn't work, you can do this...buy a Drain King at your local hardware store. When I put I. Pool Pump Not Working Humming Pool filters are the most important line of defense in keeping your pool clean, so you should know about the main types: Sand, Cartridge and D.E. (Diatomaceous Earth).

Wrap a rag over the face of the impeller so you don't damage it during removal. Intex Pool Filter Pump Not Working I've clean skimmer and pump baskets. This is a high wear and tear item within the motor. This normally is preceded by a noticeable rise in the filter pressure as indicated on the gauge atop the filter canister.

Swimming Pool Tips, Reviews & How To -MrDgvb1 129,727 views 9:14 Ask the Pool Girl: Easy Way to Prime Your Pump {Pool Maintenance} - Duration: 4:03. My Pool Pump Won't Prime Above Ground Pros 279,892 views 6:16 How To: Prime a Pool Pump - Duration: 4:57. Filter material in the pool This is a tricky issue. Pool Pump Troubleshooting Guide: A guide to help you with some of the most common problems that can occur with pool pumps.

Intex Pool Filter Pump Not Working

The start capacitor is the black cylinder on the back of the motor, which gives the motor the extra oomph it needs to start up. In such cases, the noise goes away automatically without much effort. Pool Pump Not Turning On Although the bearings are cheap (about $15) the labor is intensive. Pool Pump Not Pulling Water But these may or may not matter a whole lot.

It looks different from your filter pump because it doesn't have a strainer basket. check over here This is because it’s pumping strained and filtered water, and there should be no debris to worry about. As Americans, it's natural to want the big V8 power plant, but a pump that is too powerful could actually prevent filtration while damaging the filter and heater. To replace a Threaded Shaft type of pool pump motor, here is the procedure: Break down the pump by separating the volute or seal plate, and pull the motor back out Pool Pump Problems Low Pressure

  1. At this point you can remove the seal plate and any collars connecting to motor to the seal plate.
  2. With the power off, check that all electrical connections are tight on the timeclock and motor terminal board.
  3. For instance, a 3/4 hp Whisperflo produces the same amount of flow as a 1 1/2 hp SuperPump, at a given resistance, or head.
  4. Pump has been off now ten hours 🙁 .
  5. Also turn off the valves to the suction lines.Remove lid to the pump trap and fill with waterand re-attach lid.
  6. When you put the extender on the motor shaft, the setscrews go into a groove that runs along the shaft.

Have you checked for air leaks in the lin i.e., elbows, valves or tees? Learn More $100 OFF! Reply Matthew Simmons says: February 22, 2016 at 12:11 PM Check the hose sections fo air leaks; there may be a few pinhole sized cracks that are killing your suction power. http://brsgrp.com/pool-pump/pool-filter-motor-not-working.html If this happens it is usually because there is something wrong with the motor; however, it could be a bad breaker or one that is simply undersized for the job and

If water is spilling from the large seam between the pump seal plate, then this would be your culprit. Above Ground Pool Pump Not Working Reply Lorraine says: October 15, 2016 at 12:54 AM Hi There was a car accident yesterday which caused a power outage for about an hour. These bearings are sealed and cannot be re-packed or re-lubricated.

It will pop out easily.

I see no signs of leakage or loss of water. Reply Joe Simpson says: April 6, 2016 at 6:53 PM I'm trying to drain my pool down using the maon dtain, but the pump doesn't work now that the water level What are the model numbers of your pump and filter? Pool Pump Impeller Problems Most likely the impeller is stuck.

Pool pumps are supposed to be air tight. Whether rebuilding or replacing the motor, the Mechanical Shaft Seal should also be replaced. Pool Technicians 103,247 views 9:45 SWIMMING POOL PLUMBING SYSTEMS (800) 766 5259 www ePoolscapes com - Duration: 8:57. weblink A DIRTY FILTER CAN CAUSE THE PUMP CAVITATION (AIR IN PUMP) AS IT STRUGGLES TO PULL WATER.

Open the suction lines.Turn switch on and observe if the water is being pulled into the trap from the suction lines. Using rubber mission couplings, PVC unions or simple slip x slip couplings, reconnect the pipes you cut. We are losing prime on our pump after about 2 hours. Too low?

Turn off the power, and spin the impeller shaft.