Click here for menu

Fix Pool Pump Motor Not Working Tutorial

Home > Pool Pump > Pool Pump Motor Not Working

Pool Pump Motor Not Working

Contents

Been really dependable. If it has stretched and it seems like there is too much o-ring for the channel in the volute, soak the gasket in ice water for a few minutes to make Remove the back of the motor and run the wires in through the adapter, and tighten down the conduit adapter to secure the wires and keep out moisture and insects. Wiring up a new pump motor... http://brsgrp.com/pool-pump/pool-motor-not-working.html

If the impeller is good, you problem may be bad motor bearings. Then make sure you supply voltage matches the voltage set up on your motor and that the connections are tight. Here are the instructions for how to enable JavaScript in your web browser. If the issue in not due to source voltage, it may well be your motor. http://www.inyopools.com/Blog/8-answers-to-why-is-my-pool-pump-not-working/

Pool Pump Won't Turn On

Browse through the search results until you find the part or tool that you need. These conditions are rare, and probably will require a new pump, or a new motor. For those in the snow-belt who close down their pools your equipment has been laying dormant and needs to be put together and restarted.

Usually (but not always) 230 Volt service will have 2 wires of the same color, (and one green ground wire), while 115 Volt service will have perhaps one red (hot), one The heights and lengths are the same, which makes the plumbing job much easier. All switches on? Pool Pump Stopped Working After Storm The average flow for the pump you select should be within 10% of the pool filter's Design Flow Rate.

Is it matching the Low Voltage diagram (115 Volt), or matching the high voltage diagram (230 Volt)? Pool Pump Humming Remember to match hp and pump type and flow rate. Some pumps use a plastic impeller with a housing that holds half the seal in place.

If you have an older pump and do not want to spend the money to upgrade, consider running the pump at night when it is cooler to prevent this problem.

I'm totally lost on why it isn't working. Intex Pool Pump Won't Turn On If it's stuck, check that the impeller is not jammed with debris. Next time your pool pump motor gives you problems, see if you can solve the problem yourself instead of calling in a professional. Skimmer is closed off.

Pool Pump Humming

In some cases, it can be a bad breaker, especially one that is used often to turn the pump on and off. http://www.poolcenter.com/pumpsMotors Under pressure any leak or void in the suction side of your circulation system will result in dripping water (whereas under a vacuum it draws air in). Pool Pump Won't Turn On The motor could be seized, the capacitorbad or a wire in the rear of the motor could be disconnected or otherwise shorted. Intex Pool Pump Not Working Grasp the motor and pull it and the bracket or seal plate away from the pump volute.

If you have any rusted bolts or screws, brush them with a wire brush and give them a squirt of WD40, Liquid Wrench or other chemical bolt loosener. http://brsgrp.com/pool-pump/pool-pump-not-working-right.html Lubricants like Magic Lube (Teflon based) or Jack's Lube are always a great choice. Remove the ‘donut’ seal half of the impeller that is pressed into the seal plate with a flat head screwdriver. More commonly it may be an issue with the impeller. Pool Pump Keeps Shutting Off

  1. Remove both halves of the old seal.
  2. When your pressure is high, your filter is dirty, right?
  3. There may be a rattling as well caused by broken pieces of impeller within the housing.
  4. For a humming motor, see if the capacitor is in need of replacement.
  5. Remove the wires and the conduit adapter from the rear of the motor.
  6. If your impeller is broken then you will see little to no flow of water.

When you put the extender on the motor shaft, the setscrews go into a groove that runs along the shaft. Sometimes this might need persuasion. Lower than normal pressure on the filter corresponds with lower than normal flow rates. http://brsgrp.com/pool-pump/pool-filter-motor-not-working.html Is this an easy fix or should I call someone?

Be sure the impeller is screwed tightly onto the shaft extender before making this adjustment. Above Ground Pool Pump Problems Begin by tracing out your power supply, beginning at the breaker box. Now slide the new extender in place, lining up the setscrews along the channel, but do not tighten the setscrews.

After trial and error we figured out that it is getting moisture inside at the motor assembly.

Many suction side leaks found in this manner are then repaired with pool putty, silicone, or by replacing the leaking fitting or valve. Reply IM says: August 12, 2016 at 4:21 PM I have the same problem. Up next humming pool pump repair [ with Capacitor ] - Duration: 7:17. No Power To Pool Pump I reinstalled the motor back in the system.

Thoughts? Another way to rule out a clogged pump impeller, or an obstruction after the pump is to remove the pump lid, fill the pump with water, and turn on the pump Also is a normal pump supoposed to be quiet during its normal operation? http://brsgrp.com/pool-pump/pool-motor-humming-but-not-working.html First, screw in the conduit adapter onto the back of the motor.

Pump Trips the Breaker When the breaker trips when trying to turn on the pump, most likely the motor shaft is frozen, the impeller is stuck, or the capacitor has blown. He bypassed the gfi to see if it wood run without tripping it. Follow wiring instructions above, in previous section on installing new pumps. Thank you!

Reply Joe Simpson says: April 6, 2016 at 6:53 PM I'm trying to drain my pool down using the maon dtain, but the pump doesn't work now that the water level The solution is to get a wrench on the back of the shaft, under the centrifugal switch,and repeatedly move the shaft back and forth, to break the rust bond. Some motors offer an additional knockout on the top for wiring flexibility. They are easily removed and replaced.

NH So your pools pump has either stopped working or is malfunctioning in some way? Vaseline) for lubrication on o-rings, which can damage all types of pool o-ring rubber. Pump design and efficiency are among pool product manufacturer’s top priorities. If the shaft is not spinning then the bearings have frozen and locked up the shaft.

Add to Want to watch this again later? Thanks inyopools Posted: 07/08/2016 14:32 PM Inyo Product Specialist bt - This is typically the symptom of a wrong voltage problem. The impeller can, on stub shaft models, come loose, and hit against the impeller housing. If none of these solutions solve the problem, inspect the suction line for possible air leaks.

Check for undersized wiring. Put simply, if it’s not a pumping then you’ll be a slumpin’. Check all breakers from inside the house to any subpanel the equipment is receiving power from. The Fix: How To Replace Pool Pump Gaskets Diffuser Gasket Symptoms Losing prime Low water pressure This important but sometimes forgotten part, the diffuser and its gasket enhance the pulling power

Pump is not Pumping Water If the pump is not pumping water at all, check that all suction and return valves are open, and the pump lid is on tight, with Inyopools Posted: 07/25/2016 10:23 AM Inyo Product Specialist Bill213 - I'd take the motor out to see if the impeller is clogged or rubbing on the side of the pump.