Click here for menu

Fix Pool Pump Not Working On Low Speed (Solved)

Home > Pool Pump > Pool Pump Not Working On Low Speed

Pool Pump Not Working On Low Speed

Contents

Close the cover and hand tighten. PoolSupplyWorld Hi Barbara, an above ground pool pump uses a NEMA cord for installation and is generally smaller than an in-ground pool pump, which must be hardwired by a professional installer. Contactors Relays look significantly different depending on the brand of the spa pack. Is the bib fitting tight? navigate here

If you have a cartridge filter, try priming the pump from the pool without the cartridge in place. The impeller is functioning properly. Advanced Search Forum > Equipment - Build, Use, and Repair > Pumping Station > Pump not working on Low speed Welcome to Trouble Free Pool We would like to welcome you A little too much pressure on the screw could create more problems for you. http://www.swimming-pool-information.com/pool-pump-problems.html

Pool Pump Not Pulling Water

Filters: Diatomaceous Earth Filters are made of grids of extremely fine mesh that are coated with diatomaceous earth. Replace timer. How to to fix:( new to this pool thing just moved in haven't even used the pool yet. This sound is distinctly different from bad bearings, more of a low growling sound, or like the pump is gargling rocks.

Reply [email protected] says: February 21, 2016 at 5:31 AM Pump runs great. Remove the impeller and clean out the debris. After the pump, obstructions or clogs will cause higher pressure on the filter, so if your low flow problem is coupled with high filter pressure, check the filter, filter valve and My Pool Pump Won't Prime Electronic temperature controls are generally more reliable.

PoolSupplyWorld Hi Ken, the specs you listed sound like they're from your pump's motor, but since you want to replace the entire pool pump, we should either get the make and Pool Pump Not Working Troubleshooting Step 9 Leaks at unions on suction side - Check for leaks around the glued connection of the unions as above. There are two methods of sensing the temperature with these controls. Anonymous I just bought a new motor and wet end to replace an old Niagra Pump from waterway.

Either way, they each have two things in common, a coil, and a switch or set of large contacts. Pool Pump Won't Stay Primed We hope to see you soon! This is because the pump is not "primed" or at least not primed fully. If not, and the pressure switch is of the type that has a barbed fitting and a hose connecting it to the heater, have the new switch close by and proceed

  1. As mentioned above, it's recommended to contact a service technician who will be able to identify your pump's issues safely and confidently.
  2. To replace it, first shut off the power and then remove the two wires going to it.
  3. The contactor coil and switch terminals are generally more obvious.
  4. It was running smoothly until two days ago, and nothing out of the ordinary was done.The water is circulating but my cleaner is not moving due to low pressure.
  5. The funnel-like diffuser is then able to focus the impeller’s pulling energy, increasing its strength.
  6. Shop Terms & Conditions Privacy policy Contact us 1-877-POOLCTR | Source Code: PCRUNK | Login or Register |Live Chat | Help Center View Cart Home Pool Store Pool Parts Clearance
  7. These must be totally dried out.

Pool Pump Not Working Troubleshooting

First, make sure the pack is in the mode of operation such that it should be heating. (Low speed pump only is standard.) After each check, if a correction is made, http://www.poolspaforum.com/forum/index.php?/topic/33515-pump-2-works-on-high-speed-dosent-work-on-low-speed/ Heres a few of the MAIN causes of a pump not being fully primed or primed at all: 1)The water level has dropped below the skimmer level and the pump is Pool Pump Not Pulling Water So I deduce that it is something with my pump. Pool Pump Problems Low Pressure Some 48Y frame motors are actually thru-bolt style; therefore, check the mounting bolts to make certain they are not thru-bolt style as described below.

My label is illegible. http://brsgrp.com/pool-pump/pool-pump-not-working-right.html It may even rub enough to prevent the motor from running at all. If the GFCI trips, is there water in the blower or blower lines? Check that it is not cracked or has worn spots. Pool Pump Not Filling With Water

If your switch is connected to the manifold with flexible tubing, pull the tubing off of the switch and cap, plug, or clamp off the tubing to prevent water spillage. (If Then, check the cover itself for cracks. If none of these things fix the problem, the blower may need to be replaced. his comment is here As with any complicated piece of electrical equipment, troubleshooting and repairs are best handled by an expert.

Found screwed onto the end of the motor shaft, the impeller is a vented or veined disk. Pool Pump Won't Prime Itself If GFCI cannot be reset, you probably have water in the blower or GFCI receptacle. If wiring inside is OK, the air switch may be faulty.

Turn pump on.

Thanks! dual speed motors A single speed motor runs at the same speed all the time. After about 10 minutes it kicked the gfi breaker on the cord. Pool Pump Not Pumping Enough Water Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Hot

Inicia sesión para que tengamos en cuenta tu opinión. Simple adjustment of the tripper positions can inadvertently affect the timer dial setting whether you are aware of it or not. Be sure to mount it with the wide side of the seal facing the pump faceplate. weblink Esta función no está disponible en este momento.