Click here for menu

How To Repair Pool Pump Not Working What To Do Tutorial

Home > Pool Pump > Pool Pump Not Working What To Do

Pool Pump Not Working What To Do

Contents

If water is spilling from the large seam between the pump seal plate, then this would be your culprit. We'll I still can't get the PH up . Fortunately, we have a guide on troubleshooting a pool's low flow problems, take a look: How To Determine the Cause of Low Water Flow Reply Casey Jones says: October 23, 2015 Reply Matthew Simmons says: February 22, 2016 at 12:11 PM Check the hose sections fo air leaks; there may be a few pinhole sized cracks that are killing your suction power. navigate here

Now the pump will not turn on. Restrictions Apply. Next make sure your pool filter is clean. Remove your motor and take it in if you are not handy, or call a respected pool pro to change out the pump seal for you.IMPELLER JAM: SOMETIMES A TWIG OR http://www.inyopools.com/Blog/8-answers-to-why-is-my-pool-pump-not-working/

Pool Pump Not Working Troubleshooting

If your pump requires multiple gaskets replaced, we suggest applying a Gasket and O-ring Kit (GOKIT) if available. The water is pulled from the pool by a brass or plastic impeller that is shaft driven by an electric motor. The Fix: Replace Strainer Basket 8.) Housing Symptoms Dry rot Cracks forming near ports or bolt holes Obvious wear and tear Considered the hull of the pump, a housing encases all The key to diagnosing the pump is understanding its parts’ functions and what happens when a certain part is failing.

Sign in to make your opinion count. Reply Tammy says: July 24, 2016 at 6:16 PM I'm having a problem with the sand filter, need to put silicone on the gasket. A pool pump will "pump" air if it can; it is the path of least resistance. My Pool Pump Won't Prime If your pump is loud, the first thing to do is to listen to it.

Put simply, if it’s not a pumping then you’ll be a slumpin’. An air leak (see above) will also reduce water flow rates, as air is drawn in to the pump, and a dirty pool filter or baskets can clog up the works, Replace the defective parts and your problem will be solved.

Loading...

Again, the motor comes factory wired for 230 Volt. Above Ground Pool Pump Problems Skip navigation UploadSign inSearch Loading... Vaseline) for lubrication on o-rings, which can damage all types of pool o-ring rubber. This groove allows the screws to grip and not slide around the shaft.

Pool Pump Not Turning On

What am I doing wrong? Read More Here Loading... Pool Pump Not Working Troubleshooting Loading... Pool Pump Not Working Humming If you have an open volute, with visual access to the shaft, use straight pliers to move the shaft back and forth, until it spins free.

Putbasket back in and trap lid back on.Turn the switch back on. http://brsgrp.com/pool-pump/pool-pump-not-working-on-low-speed.html PureLine Prime October 31, 2016 Top Reasons an Above Ground Pool Needs Replacing October 28, 2016 Poolside Chat Episode #43: Finding The Right Spa Cover October 27, 2016 Archives November 2016 I'm very familiar with pumps in the commercial industry (HVAC), I'm stuck on this one though. If the pump sounds like it's gargling rocks, or there is heavy vibration noise, it may be cavitating, a term that means it's starved for water. Intex Pool Pump Not Working

If it is an oring or seal it is best to get what they call a Go Kit, which has every seal and oring in the pump, in one kit.I always Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Turn it all the way to the off position, and then back on again. his comment is here If your motor runs but turns itself off after a time, it may be over-heating.Pool pumps use a lot of wattage and need a constant supply.

Unlike the other gaskets on the list, a bad lid gasket causes a sucking leak rather than a blowout. Pool Pump Not Pulling Water Is this an easy fix or should I call someone? Without it, water won’t flow through your filtration system to be properly cleaned.

TheMichaelChaffee 301,706 views 8:57 HowTo: Repair a Pentair WhisperFlo Pump - poolplaza.com - Duration: 9:53.

Will this help the ph or mess it up? But a cycling motor may indicate that the thermal overload is kicking it off. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Pool Pump Impeller Problems I noticed that when I take the filter element out, the psi drops to 10 and the Kreepy works just fine.

Pools over 20,000 gals could possibly use the High Head pumps like, Super II, Challenger, Ultra-Flo or the Sta-Rite pumps. Pump is not Pumping Water If the pump is not pumping water at all, check that all suction and return valves are open, and the pump lid is on tight, with Pump has been off now ten hours 🙁 . http://brsgrp.com/pool-pump/pool-pump-not-working-right.html Or use a 7/16" wrench on the back of the shaft, which is usually slotted to accept an open end wrench.

Reply Matthew Simmons says: September 29, 2016 at 2:49 PM Jim - to figure this out, we will need more information about your pool upgrades. Make sure the water level is filled up. what do you think it is? Most motorswill shut off automatically if they begin to overheat.If this is the case, check the inside of the pool trap to see if any debrishas worked its way past the

I did a smoke test and saw the smoke is sucked into the pump area. Pool Technicians 103,247 views 9:45 SWIMMING POOL PLUMBING SYSTEMS (800) 766 5259 www ePoolscapes com - Duration: 8:57. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Reply IM says: August 12, 2016 at 4:21 PM I have the same problem.

The normal culprit's for a pool pump's low flow are trapped air pockets, clogged lines, sucking air leaks, or impeller issues.