Click here for menu

How To Repair Pop Up Drain Stopper Not Working Tutorial

Home > Pop Up > Pop Up Drain Stopper Not Working

Pop Up Drain Stopper Not Working

Contents

Loading... Something in the pop-up mechanism was broken. Fit the ... 15 Step 15: FinishRemove the blue protective film. Hopefully, this Instructable and others will give someone the confidence to solve a problem himself without paying someone money that is needed elsewhere in the home budget. navigate here

Please try again later. Thank you for taking the time to write this and put it online with pictures and drawings. Try This DIY Remedy Before Calling a Plumberby Jaye Denman 0hubpages.comRepairing Common Toilet Problemsby Bert Holopaw 15hubpages.comHow to Use a Drain Claw to Unclog a Bathtub Drainby Jeff Boettner 0hubpages.comHow to For example, I found the parts to fix my shower valve at http://www.deltafaucet.com/parts/index.html Thanks, Bob Reply Bridget April 21, 2015 at 9:13 pm # Hi Bob, You have the same plastic

Pop Up Sink Plug Mechanism

Or is only one required between the ball and the locking cap? TheOldkid888 183,403 views 8:37 How to Clean a Stinky Sink Drain -- by Home Repair Tutor - Duration: 5:06. Do not run water through the drain without replacing the horizontal arm and nut or covering the hole with a sponge. The installation seems pretty straightforward, but I noticed that it came with a replacement for the drain and stopper.

but, that decision is up to you. If the nut is too tight, the stopper rod will be difficult to raise and lower. Be sure to choose the one that is exactly the same size. Pop Up Bath Plug Not Working I will attempt this on Monday.

Reply Sam M-H says August 18, 2013 at 7:30 am Thanks Pretty Handy Girl. This Old House 566,745 views 4:11 Loading more suggestions... The culprit is often a buildup of hair around the base of the stopper or the pivot rod mechanism. It is usually very simple to pull out the stopper and rocker arm linkage.

I think the one I got at Home Depot, Universal Lavatory Pop-Up Ball Rod, Partsmaster Pro 58423, is exactly the same thing. Spring Loaded Sink Plug Published on Jan 26, 2012A pop-up tub train stopper can be replaced in a couple of minutes, so long as you know what you're doing. seems I have to buy a new set. Thank you again.

  1. On a bathroom sink, it's often necessary to remove the retaining nut and extract the pivot rod first.
  2. Sign in 574 55 Don't like this video?
  3. Sign in to make your opinion count.
  4. Whenthey do, they are often unsightly and an irritation.
  5. This feature is not available right now.
  6. Meanwhile, they were a mystery to me and to others.
  7. Place the linkage rod into its hole and catch the ... 14 Step 14: Install the P-trapRemove the plastic compression washer and nut for the P-trap from the old pop-up assembly.

Pop Up Bath Plug Won't Stay Down

Reply Dale Felix September 13, 2015 at 12:54 am # I am replacing the pop-up drain assembly with the same Dearborn assembly as shown in your guide. http://www.naturalhandyman.com/iip/infplumb/infpopup.html to someone else. Pop Up Sink Plug Mechanism Comments 13 commentsGo to last comment carcro5 years ago from Winnipeg Really good hub, covers stoppers and drain problems. Pop Up Drain Stopper Stuck Fix It, Plumbing, pop up drain, sink Comments Laura says December 23, 2010 at 10:05 am You're my hero!

If this happens, the rubber seal cannot correctly perform its task of properly sealing the water in the tub, and consequently the water drains out when it shouldn’t. I know a lot of folks at Instructables probably have more experience with some of these things than I do. Screw the nut back onto the drain making sure the ball joint and gasket are lined up properly. 13. Thanks! Push Down Sink Plug Not Working

essortment 134,539 views 3:31 how to replace a bathtub drain - Duration: 4:02. Bob Jackson: Thanks for the advice! When you go to the store to buy a replacement ... 2 Step 2: What goes wrongIt is tempting to think something merely separated from another part and you can restore http://brsgrp.com/pop-up/pop-up-tub-stopper-not-working.html About HomeTips Advertise Site Map Copyright Terms of Use Privacy Policy Contact HomeTips Facebook Twitter Google RSS Share This Get FREE Home Tips & HacksJoin us to get great seasonaltips,

It's much better than written instructions. Push Down Sink Plug Stuck I would use a "non-staining" version such as...
http://www.herchem.com/specs/ULTRA.pdfGreat job, Phil. I tried to upload the picture of the broken vanity drain stopper, I could not.

I love.

The lever operates a lift linkage that pulls on a spring. Bought a replacement kit, but small gaskets and used teflon tape to rig it up. I finally did but it wasn't easy. Pop Up Bath Plug Mechanism You may also need to replace the gasket or washer (or both) inside the pivot ball-and-rod assembly.

and respective owners. The instructions on the package I bought ... 4 Step 4: Disconnect the lifting rod assemblyPinch the ends of the "C"-shaped retainer clip together and slide off the end of the Reply Heidi says September 10, 2013 at 2:01 pm Thank you, thank you, thank you! The same graphic is located at the bottom of this page.

You've helped a lot of people save time, money and frustration! Reply Marylynn Swartz says November 5, 2013 at 1:25 pm I have everything apart and keep my phone with your great directions by my side. This feature is not available right now. How to Plumbing 201,602 views 3:56 How to Fix a Bathroom Sink Stopper - This Old House - Duration: 5:30.

Remove the brass lock nut with wrench. How a Sink Pop-Up Works Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body. God Bless and Happy Thanksgiving!!!!!!! Insert the pivot rod so that it engages the hole in the bottom of the stopper, and tighten on the retaining nut with the stopper in its up position.

I've spent more time than I should have on this bathroom sink job, as I couldn't get the rod into the hole in the bottom of the pop top stopper. This type of plunger produces a lot more air than the cheaper version, and so will probably do a better job of unclogging your bathtub drain. I kept both the brass and plastic drains - just in case I have a problem with the plastic drain. Too many times in the past I have had to do something later a second or a third time, but did not make enough notes.How do you keep the clip from

I suppose with the extra crud gone, it needed the adjustment I found on your instructions. Find materials, illustrations and helpful tips for quick repair. I was blank in pluming but I fix my drain stopper in 15 minutes.