Click here for menu

How To Fix Power Button Ipod Touch 4g Not Working (Solved)

Home > Power Button > Power Button Ipod Touch 4g Not Working

Power Button Ipod Touch 4g Not Working

Contents

I de-soldered the battery three points and measured the battery voltage 3.8V. Worth a try. were can i get a new piece if it is needed ? plz help Was this answer helpful? his comment is here

The use of a heat gun to soften the adhesive is highly recommended. Sometimes no matter how carefully you pry up it falls apart. Add to Want to watch this again later? This makes things much simpler for subsequent steps rather than having the front panel dangling there. https://discussions.apple.com/thread/4992083?tstart=0

Ipod Touch 4th Generation Power Button Stuck

So a few applications of these lubricants shood loosen up your power button. #14 38833, Dec 9, 2012 snowbleie President Joined: Feb 16, 2012 Messages: 767 Trophy Points: 2,460 Gender: Add a comment Add a comment Add Comment 1024 Step 10 Edit Remove the single 2.6 mm Phillips screw securing the headphone jack assembly to the rear case. kitlammers - 04/13/2013 Reply This was difficult during both disassembly and reassembly. There are 2 ribbon cables that are extremely fragile, 1 connecting the rear facing camera and another connects the volume controller flex on the logic board.

In that case, use: http://support.apple.com/kb/HT4137NB: set up as a NEW device because a software issue will be in the backup. Sign in 74 82 Don't like this video? Add a comment Add a comment Add Comment 1024 Step 25 Edit Wedge the plastic opening tool under each volume controller and pry the assembly loose from the case. Ipod Touch 4th Generation Lock Button Stuck I had the ribbon cable for the digitizer running under the LCD and that wasn't allowing the LCD to sit down far enough.

Don`t use it too much. Ipod Touch Power Button Not Working Squonky - 01/31/2015 Reply Add a comment Add Comment 1024 Step 15 Logic Board Assembly Edit With a plastic opening tool, gently pry the iPod's speaker out of its recess in Anyway when someone approaches me about this problem...

Read more here: What parts to move from the broken screen?

Note the small spring located near the bezel next to the camera (highlighted in yellow). Ipod Touch Lock Button Stuck Allow the speaker to rest above the battery so that you can proceed with battery installation. Working... I apologize, Felix, for any confusion.

Ipod Touch Power Button Not Working

The dock connector is still embedded in the frame. https://www.ifixit.com/Answers/View/104825/Lock-Wake-Power+Button+Not+Working! Yes No Voted Undo Score 0 Cancel Comments: This is one fragile piece of electronics. Ipod Touch 4th Generation Power Button Stuck So It looks like battery is OK. Ipod Nano Power Button Not Working There is also adhesive under the area shown in red. 7 comments I couldn't get a spudger in-between this space, so I went to the side where the three screws were

That metal disc is what comes in contact with the single pole single throw pushbutton they use to make the on/off closure. this content fyi...the top two connections are the power button and the bottom two are the volume control Was this answer helpful? Sign in to make your opinion count. Christmas is in a few weeks. #7 RyanJF1, Dec 9, 2012 ShawnMcCall President Joined: Oct 13, 2012 Messages: 286 Trophy Points: 1,550 Gender: Male Ratings: +68 Like x 2 Ipod Touch Power Button Not Working How To Turn Off

It looks like it's crushed and it wont come out. The logic board is still attached to the rear case. Do not try to completely separate the assembly, or you will rip this ribbon cable. weblink COMO REPARAR EL BOTON POWER. (PART 1) iDlorepair - DLO SubscribeSubscribedUnsubscribe6,0776K Loading...

it gives me trouble every time. Ipod Touch 2g Power Button Not Working In this step, you will heat each solder pad individually while using a metal spudger to pry it up from the logic board. Also what goes first in the process when doing both of those things ?

Lift the old cable out of the Touch and set it aside.

I would open it again and check the connection to the rear camera. Reassembly was tough because I didn't have the ipod dock connector seated correctly, AND more importantly, the speaker has a part that needs to be inserted into a black part on If not, de-solder the first connection and try again. Ipod Power Button Leon Stacey 309,236 views 7:43 iPOD TOUCH 4G, COMO REPARAR EL BOTON DE MENU (Parte 1) - Duration: 13:37.

yhwhelrey0 - 10/28/2013 Reply The copper is important for heat dispensing. iDlorepair - DLO 27,928 views 13:29 ipod 4th gen Power button insane fix for truly desperate - Duration: 3:02. I don't have the money to buy a new one, and I left it on the charger for a while. http://brsgrp.com/power-button/power-button-not-working-on-ipod-touch-4g.html carol - 12/29/2014 Reply Add a comment Add Comment 1024 Step 19 Edit Once all of the adhesive is freed from under the logic board/battery assembly, lift the assembly up from

jimmy - 08/04/2012 Reply Thats really bad all you have to do is buy some and replase it ben folks - 02/26/2015 Search at ebay Haris Kyritsis - 01/15/2015 Reply Add The camera does not work??? Was this answer helpful? wait a minute here....

What car adapter should I get??? HowtosendyouriPhoneinforrepair! ›iPod Touch Repairs: TouchDroppedinWater,HotTub&Pool iPodTouchputthroughthewashingmachine PartsofiPod TouchDisplayAssembly iPodTouchUpperGlass or"Screen" Repair iPodTouchLCDRepair iPodTouch1stGen"Home"buttondoesn'twork GettingyouriPodTouchbatteryreplaced ›››an overview of iPod Touch batteries Touch4thGenCamerarepair Touch4thGen"Home Key"repair GettingyouriPodTouchearphonejackreplaced RestoringstereohearingtoyouriPodTouch Touch broken"earbudtip"removal Touchpowerswitchrepair.NoOn/Off »Opinions and Analysis What I have to do? phil colbourn - 08/19/2012 Reply A strip metallic cover, glued to display isn't mentioned in this guide.

View the answer I have this problem too Subscribed to new answers Is this a good question?