of heat by the HOME BUTTON and 8 seconds on top. the perfectionist mad scientist Arrange a repair of your device, the steps involved Pricing How to Make Payment What happens when you get my device... Author with 4 other contributors Jake Devincenzi Member since: 04/18/2011 92,928 Reputation 71 Guides authored Badges: 51 +48 more badges 3 Comments Add a comment my question is for step 8. Rene Rene Jeddore - 07/09/2013 Ciao dopo aver seguito il tuo aiuto per come cambiare la batteria io ho rimontato tutto ma la barra di sblocco non scorre più o i his comment is here
Pry upward to separate the plate from the adhesive securing it to the plastic inner case. Sign in Transcript Statistics 218,606 views 380 Like this video? Sign in to add this video to a playlist. Potete aiutarmi grazie salvatore sagone - 11/05/2013 Reply I placed a penny between the battery and board and it held it in place at just the right height. https://www.ifixit.com/Answers/View/104825/Lock-Wake-Power+Button+Not+Working!
In this step, you will heat each solder pad individually while using a metal spudger to pry it up from the logic board. Oh also, not mentioned in this guide - there is a plastic/silicon substance covering the 3 leads. Please try again later. L1S2DD 32,413 views 0:59 How to fix your iPod touch 4G lock button - Duration: 2:42.
In the next few steps, you will desolder the four volume/power button ribbon cable solder joints on the logic board. asle - 01/21/2014 justinallison1, From what I understand, it is ok if that copper tape rips. Tabitha Hughes 45,246 views 15:06 iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON. Ipod Touch Lock Button Stuck or did they....
Leon Stacey 21,497 views 4:32 iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON. Ipod Touch Power Button Not Working How To Turn Off That might give it a chance to slowly unstick itself. #10 Mardigan_The_Mad, Dec 9, 2012 oOscarletOo Mayor Joined: Nov 5, 2012 Messages: 245 Trophy Points: 2,080 Gender: Male Ratings: +13 Justin Shiffler 399 views 2:30 Loading more suggestions... I have done a dozen or more iPod screens without any issue.
Loading... Ipod Power Button Should I simply desolder those pads and then resolder? Loading... Nicky Rodriguez 448,330 views 4:31 Iphone 4 power button stuck - Duration: 2:40.
the iPhone, iPad or iPod?
Lift and remove the metal cover out from the rear panel assembly. Ipod Nano Power Button Not Working Phone Repair Doctor 32,411 views 8:12 iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON. Ipod Touch 4th Generation Lock Button Stuck iPhoneTechLab 188,887 views 4:50 Power Button & Proximity Repair - iPhone 4 How to Tutorial - Duration: 8:32.
Watch Queue Queue __count__/__total__ Find out whyClose Fixing power and volume buttons in 4th gen iPod Touch Leon Stacey SubscribeSubscribedUnsubscribe11,22411K Loading... Sign in to make your opinion count. Use a plastic opening tool to pry up the adhesive around the three exposed edges of the battery. http://brsgrp.com/power-button/power-button-not-working-on-ipod-touch-4g.html William - 01/03/2014 Reply Add a comment Add Comment 1024 Step 9 Headphone Jack Edit Use an iPod opening tool to pry the headphone jack connector up and out of its
I adjusted that step, should be much easier to see now. Before final assembly, plugged it all in to test and it booted OK. LIft and remove the piece of copper tape out of the Touch. How To Turn On Ipod Without Power Button Does anyone know a good place to get a cheap 32 GB mother board??
The Glue is mostly around the top and bottom about 1/2 inch in or so, around both left and right edges the strip of glue is very thin about 1/8 inch Repeat this process with the second solder pad. iDlorepair - DLO 27,928 views 13:29 ipod 4th gen Power button insane fix for truly desperate - Duration: 3:02. check over here In almost every case the problem is the metal disc has become loose and slipped lower than it should leaving the hollowness of the button to fail to press and close
Do not try to completely separate the assembly, or you will rip this ribbon cable. Only hold the tip of the iron against the pad long enough to let the solder melt. Step 1 Front Panel Edit The iPod Touch 4th Generation front panel is attached to the rear case by adhesive. iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский язык Türkçe Machine translation Help Translate iFixit Close
Can you help me?! That will give you some advice as to what to move over from the broken screen, metal bracket, home button and small sponge spacer on the tip of the digitizer connector. No thanks Try it free Find out whyClose iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON. Rowan Whitehead 30,802 views 3:09 What to do if the Power button gets stuck on your ipod, iphone, or ipad - Duration: 0:59.
It lifted up enough from the iPod's body that I was able to slip the ribbon in around the support it sticks to and hold it in place until the adhesive Prior to desoldering remove this as much as possible with metal or plastic spudger (if metal, be sure not to bridge the connections). Working... Heat the right-most contact until the solder below melts, then apply a small amount of solder to the contact, allowing it to flow through the two holes in the cable and
Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading...